Thank You Pop-Up

It’s Sneak Peek Week for Karen Burniston’s February 2026 Release of new dies and stamps.

Today’s card uses the new die sets of Thank You Lorna Add-Ons and the Stage Pop-Up as well as the previously released Lorna Label Pop-Up. Sentiments come from the new clear stamp sets called Thank You Phrases and Love You Phrases. The new dies and stamps will be available for order starting February 2, 2026.

Watch the process video to see how I made this card.

Stage Pop-Up Base: Using the Stage Pop-Up die set, cut two of the largest die from patterned cardstock. From the same patterned cardstock, cut two of the stage-side strips.Β  After stamping and cutting the 6 decorator rectangles, glue them onto the front panels of the stage-side strips.Β  Assemble the stage platform as shown above in the video. (Below is what the completed card looks like when folded flat.)

Sentiments: The five sentiments were stamped in black ink on white cardstock and cut-out using the rectangle decorator dies from the Stage Pop-Up die set. Cut a sixth rectangle, but leave it blank to write a personal message. Use the short sentiments “For Being You,” “You’re The Best,” “For Everything” and “So Very Much” from the Thank You Phrases stamp set, and “Big Time” from Love You Phrases.

Lorna Label Thank You: Using the Thank You Lorna Add-Ons set, cut two of the large frame die from patterned paper and two sets of the words from red cardstock. From the Lorna Label Pop-Up die set, cut two of the large die from green. Glue the Thank You frames on to the green Lorna labels and adhere the letters. Add tape the the back of the Lorna Labels at the narrow bottom tip as shown in the video. Glue the green pieces back-to-back and trim off the excess flaps at the top and cut down the bottom base to fit in between the two stage halves as shown in the video.

To decorate, cut six of the leafy stems in the Thank You Lorna Add-Ons from green and glue onto the top of each of the stage sides. Cut two of the flowers in the set to add to the stage floor in front of the “Thank You.” (I used patterned paper that had daisies printed on it, so I did not use the flower center die from the set.)

Envelope: The card fits into an A7 (5×7-inches) size envelope with “Thank You” from Thank You Phrases stamped on the back flap.

___________________________________

Thank you for experiencing this blog post.

I hope this inspires you and makes you smile.

Please subscribe, like and leave comments 😊

Follow my YouTube channel, Instagram and Pinterest as well.

___________________________________

Disclaimer: Karen Burniston products are provided free of charge by the manufacturer for review and use. All other items were personally purchased. Compensated affiliate links used where or when possible, meaning I will receive a small percentage commission from these manufacturers at no cost to you. This will allow me to add more content to my YouTube channel and help out a lot. Thank you.

Materials Used:

Dies

Stamps

Papers

  • Scrapbook.com – 6Γ—8-inch Double-Sided Cardstock Patterned Collection– Berry Sweet
  • White Cardstock
  • A7 Envelope – White

Ink

  • Memento – Fade Resistant Dye ink – Tuxedo Black

Adhesives

Tools

Poinsettia Pop-Up Christmas Card

It’s Sneak Peak Week for Karen Burniston’s October 2024 release of new dies and sentiment stamps. These dies will be available for purchase on October 28, 2024 on the KB Riley LLC website.

Today’s card is an A2 size Christmas card that uses the new die sets of Poinsettia and Merry Christmas Lorna Add-Ons along with Season of Cheer stamp set.

CARDBASE: Cut an 8×6-inch rectangle of a double-sided patterned paper and fold in half to form a top-fold 4×6-inch cardbase.

LORNA LABEL: Follow the assembly video for the Lorna Label Pop-Up but cut out a frame by sandwiching the largest decorator label inside the Lorna Label die. Glue the Merry Christmas Add-Ons frame to the Lorna Label frame and decorate with words from add-on set before gluing the Lorna label pop-up into the card.

POINSETTIA: From the Poinsettia die set, cut one of the large leaves die from green and another from red. Cut one red from smaller leaves die. Brush the edges of the leaves with ink slightly darker than the cardstock. Cut the small, dotted center piece once from red and once from yellow. Save the yellow dots to inlay into the red center. Glue the large red piece onto the large green piece and then top with smaller red piece. Make sure to alternate the leaves for full coverage. Adhere red and yellow flower center. Die cut five pine branches and two of the berry stems to add around the large flower.

SENTIMENTS: The Merry Christmas Lorna Add-On set has a holly leaves shadow die that is just the right size to stamp the word β€œand” onto and glue to the bottom tip of the Lorna Label frame. The β€œand” and β€œHappy New Year” are from the Season of Cheer stamp set. The fishtail banner is a die in the Lorna Label Pop-Up set. The holly leaves and berries are in the Merry Christmas Lorna Add-On set.

___________________________________

Thank you for reading this blog post.

I hope this inspires you and makes you smile.

Please like and leave comments 😊

___________________________________

Disclaimer: Karen Burniston products are provided free of charge by the manufacturer for review and use. All other items were personally purchased. Compensated affiliate links used where or when possible, meaning I will receive a small percentage commission from these manufacturers at no cost to you. This will allow me to add more content to my YouTube channel and help out a lot. Thank you.

Materials Used:

Dies

Stamps

Papers

  • Bazzill – 8.5×11 Cardstock – Gumdrop -5-5154
  • Carta Bella – 12×12 Double-Sided Cardstock – Flora No. 4 – Bold Stems
  • Fun Stampers Journey – 8.5×11 Cardstock – Cranberry Bliss
  • Cream and Yellow Cardstock

Ink

Adhesives

Tools

Miscellaneous

  • Red Organza Ribbon 1/4-inch wide