Interactive cards

Enjoy The Waves At The Beach

| ullycatdesigns

It’s Sneak Peek week for Karen Burniston’s February 2023 release!

Standing in waist-high water at the beach letting the waves bounce you up and down is a fun childhood past-time. This card is reminiscent of those sunny, seashore visits. It uses a variety of new beach themed dies from Karen Burniston’s February 2023 release along with some new labels and frames that coordinated with the previously released Label Charm Pop-Up set.  This 3.5 x 8.5-inch card is a quick make and easily fits in a #10 business envelope. 

I started with a 3.5-inch by 8.5-inch rectangle and scored an additional 3.5-inch by 6-inch rectangle at .25-inch to form a tab along the short end. Glue this tab to the back of the large rectangle to form the card base.

Using double-sided tape, I covered the inside and outside panels with coordinating papers. (My favorite technique for using double-sided tape is to place around the edge of the card, lift the ends of the tape so corners are sticky, position the covering paper, you can shift the top paper a bit before you pull all the tape backing paper strips. See tutorial post)

Before I die-cut my Label Charm Pop-Up pivot panel into my card base, I watched the assembly video for the die and cut out the accompanying tabbed frame and label. I also cut out a large frame to edge the front aperture of the pivot panel.  I centered the pivot label charm pop-up die over the front of my card and die cut through all three layers of paper and cardstock. Because of its thickness, I ran it through my die cutting machine twice. 

Besides the frame, there are two additional labels that will fit inside the pivot panel and back tabbed label. For this card, I used the smallest of the new labels with the largest dotted border label from the original set.

Decorate the oval charm with shells from the new Sea Charms set. (I daubed a pale-yellow ink- Antique Linen on the oval charm and dotted with a gold gel pen to give the look of sand. Then I glued on stenciled shells to both sides of the oval charm.) Attach the decorated charm to the oval frame with a jump ring before assembling the pop-out elements of this card. (My jump ring had a rhinestone dangle.)

Fold the charm frame and attached label together as they will go into the card. Place a drop of glue on the frame’s tab and adhere to the back side of the card front label. Glue the blue label to the inside card back panel.

To decorate the card, I used the dancing tiny crabs from the new Beach Borders set. There are eye holes in the die that make it easy to take a white gel pen to stencil in the eyes. I added mouths for fun.

“Enjoy the Waves” come from a coordinating sentiment strip in the paper pad. “At the Beach” is die cut using the new Word Set 16 -Beach Happy Hour.

As with all my cards that are sent in an envelope, I have decorated the back flap with some dancing blue crabs to hint at what’s inside. This is #10 business envelope.

Thank you for reading this blog post. I hope this inspires you and makes you smile. Please like and leave comments 😊

Materials Used:

Dies

Papers

  • Park Lane Paperie – 12×12 Printed Cardstock – Nautical
  • Fun Stampers Journey – 8.5 x 11 Card Stock – Pumpkin Bread
  • Navy Blue and White cardstock scraps
  • Light weight white cardstock
  • #10 Business Envelope – Craft Paper

Pens & Inks

Miscellaneous

A Pirate Ship Birthday

| ullycatdesigns

I love playing with the mechanical pop-up mechanisms designed by Karen Burniston. Her Facebook page Karen Burniston Pop-Up Peeps is a place for people to post their projects using her dies. Many talented people post wonderful and creative cards and projects. One such person is John Watterson who has created several cards featuring pirates using Karen Burniston dies. His work is the inspiration for this card, and I give him all credit for the pirate figures and pirate sail. I took inspiration for the crow’s nest from him as well.

Backgrounds:  For the blue skies background on the card front, I took a piece of sky-blue cardstock and inked it using a cloud stencil, white ink and a small blending brush. Because the front scene is of a ship’s crow’s nest the viewpoint would be closer to the sky and sun, so everything would look bigger. The inside sky what also done with the white ink and just the blending brush for a more distant look of the clouds and sun. The suns are just one sun made from the Landscape Scene cut in half and the glued to the corners and trimmed again.

Rigging and Crow’s Nest:  I raided my jewelry making supplies for some brown cord to make the rigging going up the main mast. The crow’s nest is made from the larger cupcake holder from the Cupcake Pop-Up set with thin strips of the same brown paper woven through the slits and glued. I used my fingers to put a curve in the crow’s nest.

Pirate Crew:  (Click here to see John Watterson’s marooned pirate post.) While John’s pirate is on a deserted island and dancing a jig, my pirate crew are scouting the waters from the crow’s nest. I used the Monkey die set for the body and head of my pirates, took the beard from the Gnome and Santa set, and the bandana head covering from Tiny Accessories 1. The pants I fussy cut by tracing around the legs and body and cutting a bit wider than the pencils lines. The pirate is glued to the back of the crow’s nest and then adhered to the mast with foam tape.

Pirate Captain:  (Click here to see John Watterson’s pirate captain post.) John’s pirate captain sails with a spotted dog and a black cat in a basket ship. I followed John’s lead using the Gnome and Santa dies for the head, beard, coat and boots. Since John made his own hat, I did similar but used the bowler hat from the Tiny Accessories 1 for its base. The hat is cut from suede paper that I brushed with a white opaque marker to age it. I also used the eye patch from this Tiny Accessories set. The ship’s wheel is from the Cruise Charms and attached to the captain with small foam squares. His hands are from the Gnome set but glued to the wheel. I also added some white gel pen to the beard to make it stand out. My final touch was to add a parrot to the captain’s shoulder using one of the birds from the Tiny Tree set. The captain is glued to the top platform on the mini pops platform.

Ship:  The ship is based on two pop-up mechanisms – the Bam Box and the Mini Pops Pop-Up set and two of the smallest crosshatch long rectangles. The main deck base and mast are cut from a 6 1/2 x 3 1/4 inch piece of double-sided woodgrain cardstock scored and folded at 2 7/8 for the center fold using the tiered platform from the Mini Pops set. (The longer side of the cardstock is the top of the platform.) Train the large platform and top platform to pop-up as shown in the assembly video, but leave the two outer platforms as part of the base.

The main deck is a custom fitted piece cut from one of the crosshatch rectangles. And added after the bam box and its deck have been attached and tested.

The other crosshatch rectangle is folded in half and a bam box glued to the inside just at the fold. (Bam Box assembly video) (The bam box needs to fold out, away from the main deck platform so make sure to attach the box with the arched tab on top with the rubber band side next to the rectangle.) This piece now becomes the bow or front of the ship. Position the tip of the bam box so it just touches the main deck platform. Test to see that the bam box will fold down correctly before gluing in place and that the triangular point of the bow is in the center of the main deck. Cut a 90-degree triangle from the wood grain cardstock that has 2-inch sides. Trim to fit as the deck covering the bam box.

Train the bam box to open and close checking for catchpoints and trimming triangle as needed.

You will need to cut two diagonal tabs in the base bottom to hold the ship sides in place once the card is open.

Attach the main deck to its platform. Trim the back of the base to form a center mast, leaving a back railing at the height of the ship sides or taller. Trim the bottom of the base to 1/8 inch around the ship sides. Add waves to bottom of shop sides. The ship is now ready to be attached to the cardbase. Add waves to hide ship base.

Raft:  The raft is a place to write a personal message. It was made by using the thinnest die in the Long Rectangles die set to cut the planks which were trim down to approximately 3 1/4 inches. Bamboo cord was used to lash the planks together with the ends taped to the backside of the planks. Foam squares adhere the raft to the card. The stamped sentiment was fussy cut and attached to the fancy label which was cut using a die from the Label Charm Pop-Up set.

Shark & Waves:  By using a wave patterned paper, creating the ocean was easy. The waves under the ship and at the horizon line at the card’s center fold were cut using the Tropical Scene dies from light blue cardstock and inked with white ink. The gentler light blue waves in the corners were the off cuts from the waves. The shark is cut from gray cardstock and a scrap of white for his teeth using the Sea Animals set.

Sentiments:  The pirate birthday sentiments are rubber stamps by Crackerbox Stamps and were stamped in brown ink and fussy cut. Thick foam tape was used to pop the sentiments on the front of the card, while double-sided tape was used for adhering “Happy Birthday” to the raft inside.

Envelope:  While this card is designed as an 8 3/4 x 3 3/4 inch slimline card, its thickness of 1/2 inches makes it too thick to mail in a regular envelope and would need its own box or padded envelope.

Thank you for reading this blog post. I hope it provides inspiration and joy. Please like and leave comments 😊

Supplies Used:

Dies

Stamps

  • Crackerbox Stamps – Arrr Pirate Sayings set of 4

Papers

  • Colored Cardstock and Packaging Scraps
  • Hot Off the Press – Black Suede

Pens & Inks

  • Sakura – Gelly Roll Pen – Medium – White
  • Sharpie Permanent Marker – Ultra Fine Point – Black
  • Green, Orange and Yellow Fine-Tipped Markers
  • Crafter’s Square – Metallic Marker – Gold – .05 in (1.2 mm)
  • Recollections Opaque Marker – Snow
  • Stampin’ Up – Classic Stampin’ Pad – Early Espresso
  • Simon Says Stamp – Premium Pigment Ink – White

Adhesives

Tools

  • Quickstik Tool
  • Die Cutting Machine
  • Scissors
  • Craft Knife
  • Tweezers
  • Pencil
  • T-Ruler
  • Stamping Platform
  • LDRS Creative – Stampendable Stamping Tool
  • Simon Says Stamp – Blending Brush – Small
  • Craftin Desert Diva – Cloud and Pathway Stencil

Miscellaneous

•     Darice – Bamboo Cord

FlamiNgo Tower card

| ullycatdesigns

Need a fun card? Make a tower card with a honeycomb paper feature. Using products purchased from Craftstash, this card was quick to make. The flamingo and green leaves are from a Creative Craft Products bundle which includes the dies and honeycomb paper.

The card base is made with the Terrific Tower die by Sam Calcott of Made to Surprise that creates an art deco feel for this elegant display card. The front sentiment was computer generated.

.The back of the card features a die-cut “Happy Birthday” by Chole’s Creative Cards.

The card will fit in an A5 size (7 x 5 inches) envelope that has a die-cut flamingo from Karen Burniston’s Beach Charms on its back flap.

Thank you for reading this blog post. Please like and leave comments 😊

Materials Used:

Dies

Papers

Inks

  • Sharpie – Ultra Fine Point – Black
  • Staples – Liquid Stix – Hot Pink

Miscellaneous

Heart Flower Valentine

| ullycatdesigns

It’s the Karen Burniston’s Design Team February 2023 Challenge focusing on LOVE.

This hexagon flower card is a cross between an explosion box and a flower bud slowly opening. It uses two Crosshatch shape dies – Hexagons and Hearts as well as two sentiment dies – Happy Valentine’s Day and Word Set 13. An additional heart is the Circle Charm Pop-Up set.

Center Layer: Cut one of the second smallest of the plain edged hexagon in the Hexagons Crosshatch set of red 65 lb. cardstock. Cut six of the hearts in the Circle Charm Pop-Up set in red 65 lb. cardstock. Cut 12 strips 1-inch by 1/4 inch in red 65 lb. cardstock. (Strips need one squared off end that will be visible when the card is open.) Cut in white cardstock “love you” from Word Set 13.

Adhere “love you” sentiment onto hexagon parallel to a straight edge. Glue squared ends of strips to back side of the rounded tops of hearts. (Each heart should have two strips.) Place heart face up over an edge of hexagon and fold under the attached strips and glue to the underside of the hexagon. Make sure the top of the heart is just at the edge of the hexagon and not overhanging. (Overhanging hearts will make catchpoints that will be hard to open when flower is assembled.) Repeat with the next five hearts.

Fold hearts closed and test for catchpoints. Adjust attached hearts as needed to eliminate catchpoints.

Middle Layer: Cut one of the second largest of the plain edged hexagons in the Hexagons Crosshatch set in Pomegranate 100 lb. cardstock. Cut six of the smaller crosshatch heart in the Heart Crosshatch set in Pomegranate cardstock. Cut 12 strips 1-inch by 1/4 inch in Pomegranate cardstock. (Strips need one squared off end that will be visible when the card is open.)

Using thin foam squares, adhere center layer hexagon onto middle hexagon with points of smaller hexagon pointing towards the middle of each straight edge on larger hexagon. Glue squared ends of strips to back side of the rounded tops of hearts. (Each heart should have two strips.) Place heart face up over an edge of hexagon and fold under the attached strips and glue to the underside of the hexagon. Make sure the top of the heart is just at the edge of the hexagon and not overhanging. (Overhanging hearts will make catchpoints that will be hard to open when flower is assembled.) Repeat with the next five hearts.

Fold hearts closed and test for catchpoints. Adjust attached hearts as needed to eliminate catchpoints.

Outer Layer: Cut two of the largest hexagon in the Hexagons Crosshatch set – one red dotted Swiss and one white. Cut six of the scalloped heart in the Heart Crosshatch set in red dotted Swiss. Cut 12 strips 1-inch by 1/4 inch in red dotted Swiss. (Strips need one squared off end that will be visible when the card is open.)

Using thicker foam squares, adhere middle layer hexagon onto largest hexagon with points of smaller hexagon pointing towards the middle of each straight edge on larger hexagon. Glue squared ends of strips to back side of the rounded tops of hearts. (Each heart should have two strips.) Place heart face up over an edge of hexagon and fold under the attached strips and glue to the underside of the hexagon. Make sure the top of the heart is just at the edge of the hexagon and not overhanging. (Overhanging hearts will make catchpoints that will be hard to open when flower is assembled.) Repeat with the next five hearts.

Fold hearts closed and test for catchpoints. Adjust attached hearts as needed to eliminate catchpoints.

Glue white hexagon over the back of the red hexagon to cover-up strips and to provide a space to write a personal message.

Closing Band: Cut one strip of 12 inches by 3/4 inch in striped cardstock. Wrap loosely around widest part of closed flower. (Make such you can slide off the closed band before gluing closed.)

On white cardstock, trace around the “Happy Valentine’s Day” die to create a shadow for the words. Fussy cut the shadow. Die-cut the sentiment in red and use a pokey tool to weed out the words. Glue to shadow. Adhere the shadowed words to band.

The card will fit in an A2 size (4 3/8 x 5 3/4 inches) envelope. It may require extra US postage for its thickness.

You can see more Valentines by clicking here.

Thank you for reading this blog post. Please like and leave comments 😊

Materials Used:

Dies

Papers

  • Echo Park – 12×12 – A Perfect Christmas by Lori Whitlock – Snow Flack Swirl – APC135009
  • Bazzill – 8.5 x 11 – Embossed Dotted Swiss Cardstock – Red
  • Spellbinders – 8.5 x 11 – Color Essentials Cardstock 100 lb – Pomegranate
  • Recollections – 8.5 x 11 –Cardstock Paper 65 lb – Red
  • White lightweight cardstock

Miscellaneous

A String of Hearts

| ullycatdesigns

This is a quick fussy cut string of hearts using Karen Burniston’s Landscape Rectangle Accordion die. The large red hearts and smallest dark pink hearts are from the Hearts-Crosshatch set while the medium size pale pink hearts and hearts with sentiments and arrow are from the Love Charms set. (I used a purple gel pen to highlight the candy heart sentiments.)

Below is a PDF file which you can download for a basic template of how to fussy cut the panels which are connected by the smallest hearts.

hearts-accordion-scan-of-prototypeDownload

For more Accordion Fold cards click here.

A Twist and Pop Valentine

| ullycatdesigns

In cleaning up my craft room after the holidays, I came across a purchased Valentine I’d been sent many years ago with a stitched see-thru pouch with beads, sequins and the words “daughter,” sweet” and “valentine.” I decided to upcycle the card base with the pouch attached for a new Valentine.

The card base was an A6 size (5×6.5 inches). Ivory pearlescent on the outside and red on the inside. There were some tears of white on the inside where a sentiment sheet had been removed. (I hid the tears with red gingham ribbon adhered with double-sided tape.)

Using Karen Burniston’s Twist Panel Pop-Up and Heart Pivot Panels along with some of her word set dies, I recreated the card using two sheets of double-sided, printed cardstock from Craft Consortium.

I watch the assembly videos for both the Heart Pivot Panels and the Twist Panel Pop-Up before cutting and assembling my pop-up features.

Because I opted for an 8 x6 1/4-inches cardstock insert, I had to use a craft knife with a metal ruler to cut the ends of the mechanism arms free from the insert. I also die-cut a third arm from the insert cardstock which I cut-in half twice to make four strips to cover the red card base where the insert mechanism arms are cut from.

The assembly of the end panels and heart pivot panels were done as per the assembly video.  Cutting the decorative hearts from the intricate paisley cardstock makes for a somewhat non-traditional Valentine.

The sentiments inside were both cut from white cardstock but finished differently. The “love you” was also cut from a red glossy magazine page and glued off-set with the white underneath. The “Happy Valentine’s Day” had a shadow added underneath it. The shadow is cut by tracing the outside of the sentiment die on the back side of the decorative cardstock and fussy cutting. The white scalloped rectangle is cut using a decorative panel die from the Twist Panel Pop-Up set. It serves as a place for a personal message.

The outside of the card was decorated with leftover scraps of decorative cardstock and a die-cut heart I had in my stash. Because I changed the orientation of the card from a side-fold to a top-fold, I secured the see-thru pouch with glue dots and added tiny hearts to reflect the orientation.

The card will fit in an A6 size envelope. (I used an A7 envelope as I was out of A6s.) It may require extra US postage for its thickness.

You can see more Valentines by clicking here.

Thank you for reading this blog post. Please like and leave comments 😊

Materials Used:

Dies

Papers

  • Craft Consortium – 12×12 Double-Sided Premium Paper Pad – Eastern Influences
  • A6 Recycled Card Base with Valentine Pouch
  • White Cardstock
  • Red Glossy Paper Scrap
  • A7 Envelope – Ivory

Miscellaneous

Puppy Love

| ullycatdesigns

Puppy love… a dog in your life brings great joy. This is a card from a fur baby.

The adorable dog face with its moving ears, along with the front sentiment die and large paw print die-cut are all from Lynda Kanase’s i-crafter Puppy Face Wiper Inset set.

Watch the assembly video before putting together. The video recommends decorating the front and back of the card before adding items to the inside.

I masked off a banner on the front of the card using low tack paper tape. Next, I did a light spritz of a brown sparkle spray to create a sand like texture. Remove the tape and glue die-cut sentiment strip in place.

I used a left-over strip of decorative paper and two 1/8-inch tall strips of cream cardstock to finish the front of the card.

The card back uses another decorative paper scrap and a die-cut paw print that has its paw pads inked. I found that by attaching the tiny paws pads to a piece of low tack tape, I could easily ink the pieces with a sponge dauber.

I found that the puppy face dies have stencils within them that I used to ink with a white gel pen make highlights.

I added the “love you” inside the card using a Karen Burniston word set.

As with all my cards that are sent in an envelope, I have decorated the back flap with an embossing folder and a paw die-cut. Both the embossing and die-cut were inked with a dark brown ink. The card fits into an A6 envelope.

Thank you for reading this blog post. I the card made you smile and gave you inspiration. Please like and leave comments 😊

Materials Used:

Dies

Papers

  • & Papercraft, issue 204 – Pawfect Pals designed by Adam Prescott
  • Brown Craft and Cream Cardstock
  • Blue, Pink and Black Cardstock Scraps
  • A6 Card and Envelope – Ivory

Inks & Pigments

  • Nuvo Sparkle Spray – Coca Powder
  • Ranger – Tim Holtz Distress Ink – Walnut Stain
  • Sakura – Gelly Roll 08 – Gel Pen – White

Miscellaneous

We’re Off To See The Wizard!

| ullycatdesigns

Sometimes it just feels like we’re off to see the Wizard of Oz to get all our problems solved. But what we learn as we traverse the road, it’s the people we meet along the way that mean more to us than the real issue.

This is a card to let the friends you meet along the journey know you appreciate them. It uses stamps and dies by Riley and Company to recreate the characters from the movie, The Wizard of Oz. Riley of course is a moose, so it’s moose in OZ costumes.

I stamped Riley four times and then stamped the costumes for the Tin Man, Lion, Scarecrow and Dorothy from the two Oz Dress-Up sets and Toto too. Watercolor pencils were used to color the individual pieces before die-cutting out the colored pieces. I found that cutting apart the bodies made it easier to assemble the costumed moose allowing for feet and arms to be positioned in more interesting ways. (The dies cut very close to the stamped images and are very easy to line-up.)

Using a download template that I had created for other cards using multiple sliders I first printed by yellow brick paper on medium weight white cardstock and then printed the template on the back of the yellow brick paper.

split-slider-templateDownload

I had to edit the template, x-ing out some sliders and moving two others by half an inch to accommodate the size of the moose.  Using a metal ruler and craft knife I cut the red lines around each slider and then scored the blue and green lines before folding the sliders.

Before assembling the card, I stamped the sentiments on to the card front and the interactive directions on to the pull tab of the main slider piece.

Double sided tape was added to the thin tabs on the five multi-sliders. To adhere the card front to the card back, I used narrow strips of foam tape along the sides and bottom edges. Place the main slider piece with the print side down to adhere the multi-slider panels to it. Making sure it can slide between the foam tape. Peel off foam tape backing and adhere the card back.

Turn to the front to train the multi-slider panels to slide open and close. Glue figures on to the panels.

Decorate the back of the card with scraps and you can write your personal message there.

As is my usual, I stamped the envelope flap back to hint as to what is inside. I used the ruby slippers and the “Where are my freakin’ ruby slippers when I need them?” which came-out upside-down and I think sets the card up nicely for the journey.

Hope you enjoyed the card and found inspiration from it.

Here are more split easel slider cards I’ve blogged about:

Thank you for reading this blog post. Please like and leave comments 😊

Materials Used:

Dies

Stamps

Inks & Pigments

  • StazOn Solvent Ink – Jet Black
  • Ranger – Tim holtz – Distress Water Color Pencils – Sets 1, 2 & 3
  • American Crafts – Metallic Marker – Silver
  • Pigma Micron 01 – Black

Papers

  • Yellow Brick Road designed by Whimzwhirled
  • White Cardstock
  • #10 Business Envelope – Brown Craft

Miscellaneous

Tired Santa

| ullycatdesigns

This is a holiday card for a busy Santa. It features the Bam Box dies from Karen Burniston’s December 2022 release. It also uses previously released die sets of the Fireplace Pop-up die set, Fireplace Extras 1, Fireplace Extras 2,  Gnome and Santa, Slim Frames and Family Room die set.

Card Base:  The card base is an A7 size (5 x 7 inches) with a top fold. The base was what I glued decorative papers to as well as attaching the fireplace pop-up mechanism.

Bam Box:  The bam box is a rubber band powered spring box that allows the sofa to pop-up. Watch the assembly video before assembling. Heavy weight cardstock is recommended and allowing glue to dry at each step will make for the best working bam box.

Bam Box chair and ottoman closed
Bam Box chair and ottoman open

Chair:  A bam box is covered with the chair from the Family Room die set. The back of the chair is just the seat portion left flat. I cut a bam box decorative rectangle to cover the front base of the chair and hid the bam box. The pillow is attached as per assembly video directions. Santa is made from the Gnome and Santa set coloring the boots to look like socks and adding a pair of pants so his legs can stretch out onto the ottoman. Santa is glued to the pillow and his pants are glued to the Santa suit edge. The ottoman is just a bam box covered with decorative paper. (I originally was going to have a sofa in the scene as well, but decided on a chair and ottoman foot rest. The photos below depict the sofa assembly. The chair is made similarly.)

Fireplace and accessories:  For the fireplace cut two of the fireplace brick front – one in white and one in black as well as two of the lined mantle/hearth pieces – one white and one gray. The black brick is colored with a white crayon and the fire and logs are also cut twice and colored with watercolor pencils.

To assemble the fireplace, watch the assembly video first. You will need to attach the gray hearth and black brick pieces to the card base before adding the mechanism. There are two fireplace extra sets. I used the clock, fireplace fender and basket of logs from set 2 and the fireplace tools and candles from set 1. The tiny pop-up mechanisms for the objects on top of the mantel are from the fireplace die set. I also add strips of white cardstock to the wall on either side of the fireplace as floor moldings.

Rugs and Wall Decoration:  Using patterned papers that suggest wallpaper or carpeting make this type of card pop. The picture molding strip above the fireplace is a scrap trimmed off the patterned paper and the reverse side used. Slim Frames is the die set that the gold frame comes from while “Happy Boxing Day” and the calendar page are computer generated. The large green round rug is cut from the second largest circle crosshatch die. It can be used to write a personal message.

Card Front:  The card front uses a mat of silver glitter paper overlayed with the snowflake pattern plate cut from white handmade paper that has silver glitter swirls on it. The Holiday House is cut from papers used on the inside of the card. “SANTA” has been written on the door mat to hint at who is inside the card. “Happy Holidays” was cut three times with the top layer colored with silver gel pen.

Envelope: The back flap of the A7 brown kraft paper envelope has Santa’s sleigh and reindeer stamped in white to hint at what’s to come.

Thank you for reading this blog post. Please like and leave comments 😊

Materials Used:

Dies

Papers

  • Echo Park Paper Co. – 12 x12 Double-sided coated cardstock – A Perfect Christmas by Lori Whitlock – Berry Merry Christmas – APC135003
  • Echo Park Paper Co. – 12 x12 Double-sided coated cardstock – I Love Christmas by Lori Whitlock – Glad Tidings – ILC114009
  • American Crafts – The Color of memories 12 x12 Red Plaid Paper – 348968
  • Recollections – Signature Especial 12×12 Foil Paper – Silver Glitter -220520
  • White Glitter Handmade Paper
  • Colored scraps of cardstock
  • A7 Kraft Card and Envelope

Pens, Crayons & Inks

  • Pink, Red and Black Fine-Tipped Markers
  • Ranger – Tim Holtz – Distress Ink – Walnut Stain
  • Ranger – Tim Holtz – Distress Crayon – White
  • Simon Says Stamp – Premium Pigment Ink – White

Stamps

  • LeCrea Design by Leane de Graaf – Combi Stamps – Santa & Small Christmas Trees – 55.3707

Miscellaneous