Everyone likes Happy Mail and this one is made for a family of horse lovers. After making a z-fold card using a gate and fencing, I envisioned this horse paddock card.
The card is designed to fit folded into a #10 slimline envelope.
I laid-out the fence first on a 2 ½ inch x 12-inch strip of textured cardstock folding it long-ways in half and then scored at 3 inches and 9 inches. Draw pencil lines for the fence posts at: 1/4 inch, 1 7/16 inches, 1 9/16 inches, 2 7/8 inches, 3 inches, 3 1/8 inches, 4 7/16 inches, 4 9/16 inches, 5 7/16 inches, 6 1/16 inches, 7 7/16 inches,, 7 9/16 inches, 8 7/8 inches, 9 inches,, 9 1/8 inches, 10 7/16 inches, 10 9/16 inches, and 11 ¾ inches. Next, I evenly spaced three boards long-ways and colored in the spaces to be cut out. Using an Xacto craft knife and metal ruler I cut out the colored spaces on the folded over strip measuring 1 ¼ x 12 inches. (I recommend coloring in the cutout spaces as it gets very confusing, and like me, you have to start over again.) (If you have the Karen Burniston Farm Edges die set or another fence die set, you could piece together the fence rather than cutting it as I did.)
The last cutting is to trim one half of the endposts off (See photo). Once the fence is done being cut, glue the wrong sides together to form a sturdy fence. I used distress inks to color the fence.
The stable doors are sized to fit the Karen Burniston horse die. I cut three horses and decorated them differently using a black fine tipped pen and watercolor pencils. (Watch the assembly video for decoration ideas and tips). The doors are loosely based of the retired Stampin’ Up barn door set. I cut pieces of woodgrain paper to form the trim pieces and glued. The sliding door hardware is from the Stampin’Up set. Because the door is smaller than the die set door, I had to do a modified cutting of the slots that the door slides on. I followed the door assembly method described in this video by The Creativity Cave.
The sentiments are from the barn door set. You will need to cut two pieces of wood grained paper for the stable at 4 x6 inches. Once you have cut the door slots out of the front piece, and assembled the door, you can adhere the backing piece with the grain sided facing the back side of the front. (The grain will camouflage the slot cuts. Make sure you don’t glue your acetate door mechanism to the backing piece. Test your door before the glue dries if you need to make adjustments. Stamp and cut out your sentiments and adhere behind the doors. Glue one horse head to be peaking out from the stall door and the glue door onto stable.
Glue the fence endposts to the front of the stable once the doors and decorations have been added to the front of the stable. Add the horses to your paddock by gluing one to the back of the front fence and the other by using a strip of clear plastic from packaging (It needs to be sturdier than acetate.) to glue the acetate in place, first glue one side the inside of the side fencing. Fold the paddock flat to one side and see where the plastic strip folded tab ends up on the fence and, then glue to that spot.
You can write your personal message on the back of the stable.
- Stampin’Up – Barn Door stamp set – 145865
- Stampin’ Up – Sliding Door die set – 145662
- Karen Burniston in cahoots with Riley and Company – Horse, Unicorn and Zebra die set -1094
- Stampin’ Up Classic Stamin’ Pad – Chocolate Chip
- Prima Marketing Inc. Watercolor Pencils -The Basics
- Ranger – Distress Ink – Vintage Photo
- Ranger – Distress Ink – Walnut Stain
- Textured 12 x12 off white card stock from my stash
- All other papers were from my scrap bin
- PVA Glue – Cosmic Shimmer Acrylic Glue
- Foam tape
- Double-sided tear tape